Seller Needs:
$30,000|
361
|
5
Pre-owned HAAS MINI MILL 2008 Vertical Machining Center. This Vertical Machining Center has average cutting time and is equipped with a HAAS CNC Control control. This CNC Machine is currently located in Oregon. This HAAS Vertical Machining Center is available for a limited time. Get a quote today on this MINI MILL before it's gone.
Seller Needs:
Payment:
Specs:
X Axis Travel: 16"
Y Axis Travel: 12"
Z Axis Travel: 10"
Rapid Rate X Axis: 600 IPM
Rapid Rate Y Axis: 600 IPM
Rapid Rate Z Axis: 600 IPM
Table Size: 36" x 12"
Max Table Load: 500 LBS
Spindle Motor: 10 HP
Spindle Speed: 6,000 RPM
Spindle Taper: 40 CT
Tool Changer: 10 ATC
Rigid Tapping
Air and Wash Guns
Coolant System
Bearing Lubrication: Grease Packed
Cooling: Air Cooled
Max Cutting: 500 ipm
Axis Motors: 2,000 IBF Max Thrust X,Y,Z
Max Tool Diameter: 3.5"
Max Tool Weight: 12 lbs.
Chip to Chip: 5 Sec
Coolant Capacity: 40 Gal Standard
Air Required 100 PSI
Full Load AMPS 13/25
Input Voltage 240 3 Phase, 60 Cycle, 40 FLA
Dimensions: 60” x 72" x 96"
Weight: 4,850 LBS
Machine was purchased new by owner in 2008; has all original installation and equipment testing documentation from OEM representative. Machine is in pristine condition with LOW hours. Comes with Kurt machine vise, toolholders, and part probes. Machine is under power and available for inspection and testing.
Y Axis Travel: 12"
Z Axis Travel: 10"
Rapid Rate X Axis: 600 IPM
Rapid Rate Y Axis: 600 IPM
Rapid Rate Z Axis: 600 IPM
Table Size: 36" x 12"
Max Table Load: 500 LBS
Spindle Motor: 10 HP
Spindle Speed: 6,000 RPM
Spindle Taper: 40 CT
Tool Changer: 10 ATC
Rigid Tapping
Air and Wash Guns
Coolant System
Bearing Lubrication: Grease Packed
Cooling: Air Cooled
Max Cutting: 500 ipm
Axis Motors: 2,000 IBF Max Thrust X,Y,Z
Max Tool Diameter: 3.5"
Max Tool Weight: 12 lbs.
Chip to Chip: 5 Sec
Coolant Capacity: 40 Gal Standard
Air Required 100 PSI
Full Load AMPS 13/25
Input Voltage 240 3 Phase, 60 Cycle, 40 FLA
Dimensions: 60” x 72" x 96"
Weight: 4,850 LBS
Machine was purchased new by owner in 2008; has all original installation and equipment testing documentation from OEM representative. Machine is in pristine condition with LOW hours. Comes with Kurt machine vise, toolholders, and part probes. Machine is under power and available for inspection and testing.
Options:
HAAS CNC Control
Probe
(20) Toolholders
(1) 6 x 7-1/2" Kurt Machine Vise
(1) Renishaw Optical Tool Setter Probe
(1) Renishaw Optical Transmission Part Probe
Probe
(20) Toolholders
(1) 6 x 7-1/2" Kurt Machine Vise
(1) Renishaw Optical Tool Setter Probe
(1) Renishaw Optical Transmission Part Probe
Seller:
JerrS494
Location:
OR
