What is F in G-code? Understanding Feed Rate in CNC Programming

Article Categories

  • CNC Lathe(29)
  • Vertical Machining Center(18)
  • Horizontal Machining Center(17)
  • EDM(15)
  • Router(13)
  • 3D Printer(5)
  • Laser(5)
  • Aluminum(1)
  • Brass(1)
  • Copper(1)
  • Grinding(1)
  • Handling(1)
  • Inspection(1)
  • Punch Press(1)
  • Steel(1)
  • Titanium(1)
  • Waterjet(1)
Select Category
What is F in G-code? Understanding Feed Rate in CNC Programming

What is F in G-code? Understanding Feed Rate in CNC Programming

When working with CNC machines, mastering G-code is essential for creating precise, efficient toolpaths. One of the most important — and often misunderstood — commands in G-code is the “F” word, which stands for Feed Rate.

Whether you're cutting metal, plastic, or composites, the F command tells your CNC machine how fast the tool should move through the material. In this article, we’ll explain what F in G-code means, how it works, and how to use it effectively in CNC programming.

🛠️ What Does “F” Mean in G-code?

In G-code, the letter F specifies the feed rate — the speed at which the cutting tool or machine moves along its programmed path. The feed rate is typically measured in:

  • Inches per minute (IPM) when using G20 (inch mode)
  • Millimeters per minute (mm/min) when using G21 (metric mode)

✅ Basic Syntax of the F Command

G01 X50 Y25 F100

This line tells the machine to:

  • Use linear interpolation (G01)
  • Move to coordinates X50 Y25
  • At a feed rate of 100 units per minute (IPM or mm/min depending on mode)

📌 When is F Used?

The F command is most commonly used with:

  • G01 – Linear cutting moves
  • G02 / G03 – Circular interpolation (arcs)
  • Drilling cycles – Like G81, G83, etc.

It is not used during rapid positioning (G00), since G00 ignores feed rate and moves as fast as possible.

📏 Feed Rate Units in G-code

Command Mode Feed Rate Units
G20 Inch mode Inches per minute (IPM)
G21 Metric mode Millimeters per minute (mm/min)

⚙️ How F Affects Machining

Choosing the right F value is crucial. Too fast and you risk:

  • Tool breakage
  • Poor surface finish
  • Overheating

Too slow and you’ll:

  • Waste cycle time
  • Increase tool wear due to rubbing

Feed rates depend on:

  • Material hardness
  • Tool type & diameter
  • Spindle speed (S)
  • Depth of cut

💡 Best Practices for Using F in G-code

  1. Start with Manufacturer Recommendations: Use speeds and feeds provided by tool suppliers.
  2. Test and Adjust: Simulate and fine-tune based on chip load and surface finish.
  3. Use Consistent Units: Don’t mix G20 and G21 without resetting your F values accordingly.
  4. Keep It Safe: Use slower feed rates for setup runs or testing new toolpaths.
  5. Don’t Re-enter F Unnecessarily: Once set, F stays active until changed — no need to repeat unless adjusting.

🧠 F vs S in G-code

F = Feed Rate (how fast the tool moves through the material)

S = Spindle Speed (how fast the tool spins, in RPM)

Both must be optimized together for best cutting performance.

🧮 Quick Example: Feed Rate Formula (For Milling)

To calculate feed rate:

Feed Rate (IPM) = RPM × Number of Flutes × Chip Load

This gives you a baseline to use with your F command in G-code.

Conclusion

The F in G-code is a fundamental parameter that controls your feed rate — the speed at which the cutting tool moves through the material. Whether you're milling, drilling, or contouring, getting your feed rate right ensures better part quality, longer tool life, and faster production.

Always pair feed rate with proper spindle speed, tool selection, and material considerations to optimize your CNC machining performance.

Related Searches:

  • What is feed rate in CNC machining?
  • G01 vs G00 in G-code
  • How to calculate speeds and feeds
  • G-code cheat sheet for beginners

Need help programming your next CNC job? Visit CNCMachines.com to find expert tips, tools, and top-quality CNC machines for any application.

Article Categories

  • CNC Lathe(29)
  • Vertical Machining Center(18)
  • Horizontal Machining Center(17)
  • EDM(15)
  • Router(13)
  • 3D Printer(5)
  • Laser(5)
  • Aluminum(1)
  • Brass(1)
  • Copper(1)
  • Grinding(1)
  • Handling(1)
  • Inspection(1)
  • Punch Press(1)
  • Steel(1)
  • Titanium(1)
  • Waterjet(1)
Select Category

Similar ListingsSEE ALL 8 NEW LISTINGS

HAAS DS30Y #16777
HAAS DS30Y #16777
US FlagUSA
2019 HAAS DS30Y
CNC Lathe  #16777   View Listing
Chuck 8" • Bar 2" • Bar Feeder • 
$119,500
HAAS ST30Y #16776
HAAS ST30Y #16776
US FlagUSA
2020 HAAS ST30Y
CNC Lathe  #16776   View Listing
Chuck 10" • Bar 3" • Chip Conv • 
$108,000
HAAS UMC750 #16727
HAAS UMC750 #16727
US FlagUSA
2018 HAAS UMC750
Vert Mach Center  #16727   View Listing
TSC • Probe • Chip Conv • 
Call For Price
HAAS VF4SS #16770
HAAS VF4SS #16770
US FlagUSA
2019 HAAS VF4SS
Vert Mach Center  #16770   View Listing
50"x20"x25" • 
Call For Price
HAAS TL1 #16711
HAAS TL1 #16711
US FlagUSA
2005 HAAS TL1
CNC Lathe  #16711   View Listing
Chuck 8" • Bar 2" • Tailstock • 
$19,000
OKUMA LB300 #16769
OKUMA LB300 #16769
US FlagUSA
2007 OKUMA LB300
CNC Lathe  #16769   View Listing
Chip Conv • Tool Presetter • Tailstock • 
Call For Price
HAAS VM3 #16767
HAAS VM3 #16767
US FlagUSA
2011 HAAS VM3
Vert Mach Center  #16767   View Listing
40"x26"x25" • Probe • Chip Conv • 
Call For Price
LEGACY CNC WOODWORKING MAVERICK 4X8 #16701
LEGACY CNC WOODWORKING MAVERICK 4X8 #16701
US FlagUSA
2018 LEGACY CNC WOODWORKING MAVERICK 4X8
Router  #16701   View Listing
Dust Collector • 
$22,000